ENGLISH
10 1. INTRODUCTION1. INTRODUCTIONThank you very much for choosing an EIZO Color LCD Monitor.1-1. Features• Dual inputs compliant (D-Sub mini 15 pin x
1. INTRODUCTION 11ENGLISH 1-2. Package ContentsPlease contact your local dealer for assistance if any of the listed items are missing ordamaged.• LCD
12 1. INTRODUCTION(2)(3)(4)(5)(6)(7)(8)(1)1-3. Controls & ConnectorsFront(1) ScreenManager™(2) Power Terminal Covers for the Optional peripheral(3
1. INTRODUCTION 13ENGLISH ( 9) (10) (12) (13) (14) (15) (16)(11)Rear(9) Main Power Switch(10) 4 Holes for Mounting an Arm-Stand*2(11) Stand (Det
14 2. CABLE CONNECTION2. CABLE CONNECTION2-1. Before connectingBefore connecting your monitor to the PC, change the display screen settings (resolutio
2. CABLE CONNECTION 15ENGLISH2-2. Connecting the signal cable• Be sure that the power switches of both the PC and the monitor are OFF.1. Remove the re
16 2. CABLE CONNECTION3. Plug the power cord into the power connector on the rear of themonitor. WARNING• Use the enclosed power cord. If using the p
3. ScreenManager 17ENGLISH3-1. How to use the ScreenManagerAs shown on the display, the ScreenManager is used to adjust the LCD monitor.ScreenManager
18 3. ScreenManager3-2. ScreenManager Adjustments and SettingsThe following table shows all the ScreenManager’s adjustment and setting menus.Main menu
3. ScreenManager 19ENGLISH3-3. Useful FunctionsAdjustment LockUse the “Adjustment Lock” function to prevent any accidental changes.Locked function • A
2SAFETY SYMBOLSThis manual uses the safety symbols below. They denote critical information. Pleaseread them carefully. WARNINGFailure to abide by
20 4. ADJUSTMENT4. ADJUSTMENT4-1. Screen AdjustmentScreen adjustments for the LCD monitor should be used in suppressing screen flickeringand also for
4. ADJUSTMENT 21ENGLISH3. Adjust by using “Screen” menu in the ScreenManager.(1) Vertical bars appear on the screen.Use the “Clock”p.42) adjustmentSel
22 4. ADJUSTMENT(3) The screen position is incorrect.Use the “Position” adjustmentThe correct displayed position of LCD monitor is decided because the
4. ADJUSTMENT 23ENGLISH4. Set the Output signal range (Dynamic Range) of the signal.Perform the “Range Adjustment”p.43)This controls the level of outp
24 4. ADJUSTMENT 4-2. Displaying a low resolutionsThe lower resolutions are enlarged to full screen automatically. Using the “Screen Size”function in
4. ADJUSTMENT 25ENGLISH2. Smooth the blurred texts of the enlarged screen.Adjust the “ Smoothing”Some lines of the texts or pictures may appear with t
26 4. ADJUSTMENT4-3. Color AdjustmentThe “ColorManagement”menu in the ScreenManager enables to change the color of thescreen.Before the Color adjustme
4. ADJUSTMENT 27ENGLISH2. To change the saturation.Adjust the “Saturation”The saturation can be selected from -16 ~ 16. Setting the minimum level (-1
28 4. ADJUSTMENT4-4. Power-save SetupThis monitor complies with the VESA DPMSp.43) standard and adopts a power savingmethod, EIZO MPMS p.42), which
5. MAKING USE OF USB (Universal Serial Bus) 29ENGLISH5. MAKING USE OF USB (Universal Serial Bus)This monitor provides a hub which supports the
TABLE OF CONTENTS 3ENGLISHTABLE OF CONTENTS PRECAUTIONS... 41. INTRODUCTION
30 5. MAKING USE OF USB (Universal Serial Bus)3. After setting up, the monitor’s USB hub is available for connecting USB compliantperipherals to the d
6. CONNECTING TWO PCs TO THE MONITOR 31ENGLISHInput SignalSelection Button6. CONNECTING TWO PCs toTHE MONITORTwo PCs can be connected to the monitor t
32 6. CONNECTING TWO PCs TO THE MONITORThe priority input signalThis function is used to select which PC will have priority to control the monitorwhen
7. ATTACHING AN ARN STAND 33ENGLISH7. ATTACHING AN ARM STANDThe LCD monitor can be used with an arm stand by removing the tilt stand andattaching the
34 7. ATTACHING AN ARN STAND2. Remove the stand by loosening the screws.(4 pcs of 4 x 10 S-Type Ni/Fe)3. Attach an arm stand to the LCD monitor secure
8. TROUBLESHOOTING 35ENGLISH8. TROUBLESHOOTINGIf a problem persists even after applying the suggested remedies, contact an EIZOdealer. No picture prob
36 8. TROUBLESHOOTING Problems Points to check with possible solutions3. Display position isincorrect.4. Screen image is smalle
8. TROUBLESHOOTING 37ENGLISH Problems Points to check with possible solutionsThis is due to the characteristics of the panel it
38 8. TROUBLESHOOTING Problems Points to check with possible solutionsUse the graphics board’s utility software to change thein
9. CLEANING 39ENGLISH9. CLEANINGPeriodic cleaning is recommended to keep the monitor looking new and to prolong itsoperation lifetime.WARNING´ Keep li
4 PRECAUTIONS PRECAUTIONS WARNING´ If the monitor begins to emit smoke, smells like something isburning, or makes strange noises, disconnect all power
40 10. SPECIFICATIONS10.SPECIFICATIONSLCD Panel 50 cm (19.6 inch), TFT color LCD panel with Anti-Glare Hard CoatingViewing Angle: Horizontal: 150º,
10. SPECIFICATIONS 41ENGLISHDefault settingDefault setting are as follows:•Contrast 100 %•Brightness 100 %•Smoothing 3•Color Standard mode/Off (Temper
42 11. GLOSSARY11.GLOSSARYAfterimageThe Afterimage is particular to LCD monitors when the monitor screen is left on fora long period without use. The
11. GLOSSARY 43ENGLISHRange AdjustmentThe Range Adjustment controls the level of output signal range to display the wholecolor gradation ResolutionThe
44 12. INDEX12.INDEXAADJUSTMENT --------------------------- 20Adjustment Lock ------------------------- 19Afterimage ----------------------------- 19,
APPENDIXAPPENDIXAPPENDIX / ANHANG / ANNEXEPreset Timing Chart for Analog inputTiming-Übersichten für Analog EingangSynchronisation des Signaux pour An
xlvi APPENDIXMode Dot Clock Frequencies A: Front Porch B: Sync PeriodMHz H V H V H VkHz Hz µs/ ms/ µs/ ms/Dot Line Dot LineVGA 0.636/ 0.318/ 3.813/ 0.
APPENDIXAPPENDIXC: Back Porch D: Blanking Period E:Display Period F:Total CycleHV H V H V HVµs/ ms/ µs/ ms/ µs/ ms/ µs/ ms/Dot Line Dot Line Dot Lin
xlviii APPENDIX 33.5(1.3)Pin AssignmentPin-BelegungAffectation des Broches* D-Sub mini 15 pin connectorPin No. Signal Pin No. Signal1 Red video 9 No p
APPENDIXAPPENDIXMEMO
PRECAUTIONS 5ENGLISH WARNING´ Keep small objects away from the monitor.Small objects may accidentally fall through the ventilation slots into thecabin
Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a product developedfor professional u
Environmental requirementsFlame retardantsFlame retardants are present in printed circuit boards, cables, wires, casings andhousings. Their purpose is
FCC Declaration of ConformityWe, the Responsible Party EIZO NANAO TECHNOLOGIES INC.5710 Warland Drive, Cypress, CA 90630Phone: 562 431 5011declare th
For Europe, etc. (220-240 Vac) OnlyCE MarkingDeclaration of ConformityKind of equipment: MonitorType-designation: L771is in compliance with:Council Di
6 PRECAUTIONSOK WARNING• Use the enclosed power cord. If using the power cord other than theenclosed one, follow these guidelines.[USA and Canada]Use
PRECAUTIONS 7ENGLISH WARNING´ Install the monitor securely when attaching to an arm stand.When attaching an arm stand, please refer to the user’s manu
8 PRECAUTIONS CAUTION´ Do not block the ventilation slots on the cabinet.* Do not place books or any other papers on the ventilation slots.* Do not in
PRECAUTIONS 9ENGLISHSuggestions for Maximizing Comfort´ To lessen the chance of possible injury and to increase yourcomfort and productivity while you
Comments to this Manuals